"Plastics V Determina" CNS Standards Search Result

1. Ready translated english version CNS Standards ( SALE mark ) and Chinese version CNS Standards, you can purchase directly in the web page; After receive your payment, we will send the CNS Standards PDF file to your Email within 1~3 days.
2. Other English version CNS Standards are not ready translated, only after get your order, then we translate them, time usually need more 3-5 days .


	CNS 7046-1 - English Version Plastics piping systems − Polyethylene piping materials and components − Determination of volatile content 冷熱水裝置用塑膠管配管系統－聚丁烯(PB)－第1部：通則 - 英文版
	CNS 15914 - English Version Thermoplastics pipes for the conveyance of fluids − Determination of resistance to rapid crack propagation (RCP) − Small-scale steady-state test (S4 test) 流體輸送用熱塑性塑膠管－耐快速裂痕擴展(RCP)之測定－小型穩態(S4)試驗 - 英文版
	CNS 15915 - English Version Thermoplastics pipes for the conveyance of fluids − Determination of resistance to rapid crack propagation (RCP) − Full-scale test (FST) 流體輸送用熱塑性塑膠管－耐快速裂痕擴展(RCP)之測定－全尺度試驗(FST) - 英文版
	CNS 5846-1 - English Version Plastics - Determination of ash - Part 5: Poly (vinyl chloride) 塑膠－沙丕(Charpy)衝擊性能測定法－第1部：非儀器式衝擊試驗 - 英文版
	CNS 6834-5 - English Version Testing methods for rubber and plastics hoses - Part 5: Determination of electrical resistance and conductivity 橡膠管及塑膠管試驗法－第5部：電阻與導電係數之測定 - 英文版
	CNS 15852-2 - English Version Thermoplastics pipes, fittings and assemblies for the conveyance of fluids − Determination of the resistance to internal pressure − Part 2: Preparation of pipe test pieces 流體輸送用熱塑性塑膠管、管件及組合件－耐內壓力測定－第2 部：管試件製備 - 英文版
	CNS 15612 - English Version Plastics − Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics − Part 1: Standard method 塑膠－吸水率測定法 - 英文版
	CNS 15605-1 - English Version Plastics − Determination of refractive index 塑膠－受負荷下之撓曲溫度測定法－第１部：一般試驗法 - 英文版
	CNS 15852-1 - English Version Thermoplastics pipes, fittings and assemblies for the conveyance of fluids − Determination of the resistance to internal pressure − Part 1: General method 流體輸送用熱塑性塑膠管、管件及組合件－耐內壓力測定－第1 部：一般方法 - 英文版
	CNS 6834-3 - English Version Testing methods for rubber and plastics hoses - Part 3: Determination of resistance to vacuum 橡膠管及塑膠管試驗法－第3部：耐負壓試驗 - 英文版
	CNS 15645 - English Version Rigid cellular plastics – Determination of water vapour transmission properties 硬質發泡塑膠－透濕性質測定法 - 英文版
	CNS 8516-1 - English Version Plastics − Determination of tensile properties − Part 5: Test conditions for unidirectional fibre-reinforced plastic composites 塑膠－熱塑性塑膠熔融質量流率(MFR)與熔融體積流率(MVR)之測定法－第1 部：標準方法 - 英文版
	CNS 2828 - English Version Plastics − Reinforced moulding compounds and prepregs − Determination of apparent volatile-matter content 塑膠－狀態調節及試驗之標準大氣狀態 - 英文版
	CNS 15638 - English Version Rigid cellular plastics – Determination of compressive creep under specified load and temperature conditions 硬質發泡塑膠－規定載重與溫度狀態下之壓縮潛變測定法 - 英文版
	CNS 15363 - English Version Determination of the ultimate aerobic biodegradability of plastics in soil by measuring the oxygen demand in a respirometer or the amount of carbon dioxide evolved 藉由量測呼吸計內需氧量或二氧化碳釋出量測定土壤中塑膠之好氧生物分解度 - 英文版
	CNS 4394-1 - English Version Plastics − Homopolymer and copolymer resins of vinyl chloride − Determination of volatile matter (including water) 塑膠－熱塑性塑膠射出成型試片－第1部：通則及模製多用途與棒形試片 - 英文版
	CNS 15637 - English Version Rigid cellular plastics – Determination of compressive creep 硬質發泡塑膠－壓縮潛變測定法 - 英文版
	CNS 5342 - English Version Plastics − Determination of loss of plasticizers in plastics − Activated carbon method 塑膠－塑膠品中塑化劑遷移性測定法 - 英文版
	CNS 15641 - English Version Rigid cellular plastics – Determination of the volume percentage of open cells and of closed cells 硬質發泡塑膠－開放與封閉氣泡體積百分率測定法 - 英文版
	CNS 6187 - English Version Paints, varnishes and plastics − Determination of non-volatile-matter content 油漆、清漆及塑膠－不揮發物含量測定法 - 英文版
	CNS 3142-1 - English Version Plastics − Thermoplastic materials − Determination of Vicat softening temperature (VST) 塑膠－硬質聚氯乙烯板片－第1部：厚度1 mm以上平板之種類、尺度及特性 - 英文版
	CNS 15852-4 - English Version Thermoplastics pipes, fittings and assemblies for the conveyance of fluids − Determination of the resistance to internal pressure − Part 4: Preparation of assemblies 流體輸送用熱塑性塑膠管、管件及組合件－耐內壓力測定－第4部：組合件製備 - 英文版
	CNS 15524-5 - English Version Plastics - Determination of ash - Part 5: Poly (vinyl chloride) 塑膠－灰分測定法－第5部：聚氯乙烯 - 英文版
	CNS 6834-3 - English Version Testing methods for rubber and plastics hoses - Part 3: Determination of resistance to vacuum 橡膠管及塑膠管試驗法－第3部：耐負壓試驗 - 英文版
	CNS 6834-5 - English Version Testing methods for rubber and plastics hoses - Part 5: Determination of electrical resistance and conductivity 橡膠管及塑膠管試驗法－第5部：電阻與導電係數之測定 - 英文版
	CNS 15852-3 - English Version Thermoplastics pipes, fittings and assemblies for the conveyance of fluids − Determination of the resistance to internal pressure − Part 3: Preparation of components 流體輸送用熱塑性塑膠管、管件及組合件－耐內壓力測定－第3部：組件製備 - 英文版

Find out:26Items | To Page of: First -Previous-Next -Last | 1