Cart:
| Standard Code | Standard Title | Standard Class | Order |
|---|---|---|---|
| GB/T 45021.1-2024 |
Photovoltaic module performance test and energy assessment-Part 1: Irradiance and temperature performance measurement and power assessment {译} 光伏组件性能测试和能量评定-第1部分：辐照度和温度性能测量和功率评定 |
China National Standards temperature |
 English PDF |
| GB/T 45171-2024 |
Determination of the temperature of the contact surface of plastic food contact materials and products with food under microwave heating conditions {译} 塑料类食品接触材料及制品在微波加热条件下与食品接触面温度的测定 |
China National Standards temperature |
English PDF |
| GB/T 44916-2024 |
Ships and marine technology-Marine ultra-low temperature gate valves-Design and test requirements {译} 船舶和海上技术-船用超低温闸阀-设计与试验要求 |
China National Standards temperature |
English PDF |
| GB/T 45012-2024 |
Industrial insulation products-Determination of low-temperature linear thermal expansion coefficient {译} 工业用绝热制品-低温线性热膨胀系数的测定 |
China National Standards temperature |
English PDF |
| GB/T 44911-2024 |
Aircraft - Environmental and operating conditions for airborne equipment - Humidity, temperature and atmospheric pressure tests {译} 航空器-机载设备环境和操作条件-湿度、温度和大气压力试验 |
China National Standards temperature |
English PDF |
| GB/T 18281.5-2024 |
Sterilization of healthcare products - Biological indicators - Part 5: Biological indicators for low-temperature steam formaldehyde sterilization {译} 医疗保健产品灭菌-生物指示物-第5部分：低温蒸汽甲醛灭菌用生物指示物 |
China National Standards temperature |
English PDF |
| GB/T 44956-2024 |
Weather forecast verification Precipitation and temperature {译} 天气预报检验 降水和温度 |
China National Standards temperature |
English PDF |
| GB 4716-2024 |
Point-type temperature-sensitive fire detector {译} 点型感温火灾探测器 |
China National Standards temperature |
English PDF |
| GB/T 20154-2024 |
Low-temperature storage boxes {译} 低温保存箱 |
China National Standards temperature |
English PDF |
| GB/T 42125.4-2024 |
Safety requirements for electrical equipment for measurement, control and laboratory use-Part 4: Special requirements for climate and environmental testing and other temperature regulation equipment {译} 测量、控制和实验室用电气设备的安全要求-第4部分：气候与环境试验以及其他温度调节设备的特殊要求 |
China National Standards temperature |
English PDF |
| GB/T 44753-2024 |
Test methods for liquidus temperature of ultra-thin glass {译} 超薄玻璃液相线温度试验方法 |
China National Standards temperature |
English PDF |
| GB/T 4074.7-2024 |
Winding wire test method-Part 7: Test method for determining the temperature index of enameled winding wire {译} 绕组线试验方法-第7部分：测定漆包绕组线温度指数的试验方法 |
China National Standards temperature |
English PDF |
| GB/T 44744-2024 |
Grain storage - Technical regulations for low-temperature grain storage {译} 粮食储藏-低温储粮技术规程 |
China National Standards temperature |
English PDF |
| GB/T 44537-2024 |
Fine ceramic room temperature fracture toughness test method-Surface crack bending beam (SCF) method {译} 精细陶瓷室温断裂韧性试验方法-表面裂纹弯曲梁（SCF）法 |
China National Standards temperature |
English PDF |
| GB/T 25831-2024 |
Deformed high-temperature alloys - wires {译} 变形高温合金-丝材 |
China National Standards temperature |
English PDF |
| GB/T 44549-2024 |
Test method for interfacial bonding strength of ceramic materials under high temperature conditions {译} 高温条件下陶瓷材料界面黏结强度试验方法 |
China National Standards temperature |
English PDF |
| GB/T 44341-2024 |
Determination of total sulfur content in fertilizers - High temperature combustion method {译} 肥料中总硫含量的测定-高温燃烧法 |
China National Standards temperature |
English PDF |
| GB/T 5169.13-2024 |
Fire hazard testing for electrical and electronic products - Part 13: Basic test methods for glowing wire/hot wire - Glow wire ignition temperature (GWIT) test method for materials {译} 电工电子产品着火危险试验-第13部分:灼热丝/热丝基本试验方法-材料的灼热丝起燃温度（GWIT）试验方法 |
China National Standards temperature |
English PDF |
| GB/T 44319-2024 |
Isotope temperature difference batteries for lunar and deep space exploration {译} 月球与深空探测用同位素温差电池 |
China National Standards temperature |
English PDF |
| GB/T 2423.65-2024 |
Environmental testing - Part 2: Test methods - Test: salt spray/temperature/humidity/solar radiation combination {译} 环境试验-第2部分：试验方法-试验：盐雾/温度/湿度/太阳辐射综合 |
China National Standards temperature |
English PDF |
| GB/T 2424.7-2024 |
Environmental testing - Part 3: Supporting documents and guidelines - temperature chamber measurements (with load) for test A (low temperature) and B (high temperature) {译} 环境试验-第3部分：支持文件及导则-试验A（低温）和B（高温）的温度箱测量（带负载） |
China National Standards temperature |
English PDF |
| GB/T 2423.34-2024 |
Environmental testing - Part 2: Test methods - Test Z/AD: temperature/humidity combined cycle test {译} 环境试验-第2部分：试验方法-试验Z/AD:温度/湿度组合循环试验 |
China National Standards temperature |
English PDF |
| GB/T 44304-2024 |
Test method for fracture resistance of fine ceramics at room temperature - Indentation (IF) method {译} 精细陶瓷室温断裂阻力试验方法-压痕（IF）法 |
China National Standards temperature |
English PDF |
| GB/T 44371-2024 |
Critical bending diameter measurement - Critical bending diameter measurement of Bi-2223 superconducting tape in liquid nitrogen temperature zone {译} 临界弯曲直径测量-液氮温区Bi-2223超导带材的临界弯曲直径测量 |
China National Standards temperature |
English PDF |
| GB/T 44279-2024 |
temperature-humidity-vibration-low pressure comprehensive environmental test system {译} 温度-湿度-振动-低气压综合环境试验系统 |
China National Standards temperature |
English PDF |
| GB/T 31078-2024 |
Specifications for low-temperature storage operations {译} 低温仓储作业规范 |
China National Standards temperature |
English PDF |
| GB/T 44148.3-2024 |
Steel forgings, rolled or forged steel bars for pressure equipment-Part 3: Low temperature toughness nickel steel {译} 承压设备用钢锻件、轧制或锻制钢棒-第3部分:低温韧性镍钢 |
China National Standards temperature |
English PDF |
| GB/T 44148.2-2024 |
Steel forgings, rolled or forged steel bars for pressure equipment-Part 2: Low alloy and alloy (molybdenum, chromium and chromium-molybdenum) steels with specified high temperature properties {译} 承压设备用钢锻件、轧制或锻制钢棒-第2部分：规定高温性能的低合金及合金（钼、铬和铬钼）钢 |
China National Standards temperature |
English PDF |
| GB/T 44139.1-2024 |
Requirements for sleeping bags - Part 1: Thermal performance, quality and size requirements for sleeping bags designed for extreme low temperatures above -20°C {译} 睡袋的要求-第1部分：设计用于极限低温-20℃以上睡袋的热性能、质量和尺寸要求 |
China National Standards temperature |
English PDF |
| GB/T 22459.9-2024 |
Refractory mud - Part 9: Test method for shear bond strength at room temperature {译} 耐火泥浆-第9部分：常温抗剪粘接强度试验方法 |
China National Standards temperature |
English PDF |
| GB/T 44030-2024 |
Metallic materials-High temperature compression test methods {译} 金属材料-高温压缩试验方法 |
China National Standards temperature |
English PDF |
| GB/T 18153-2024 |
Safety of machinery - Safety data for determining the temperature limit of accessible hot surfaces {译} 机械安全-用于确定可接触热表面温度限值的安全数据 |
China National Standards temperature |
English PDF |
| GB/T 43853-2024 |
High-temperature Friction and Wear Performance Test of Laser Repair Layer-Ball-disc Method {译} 激光修复层高温摩擦磨损性能试验-球-盘法 |
China National Standards temperature |
English PDF |
| GB/T 43870.1-2024 |
Measurement method of Curie temperature of magnetic materials - Part 1: permanent magnetic materials {译} 磁性材料居里温度的测量方法-第1部分：永磁材料 |
China National Standards temperature |
English PDF |
| GB/T 43870.2-2024 |
Measurement method of Curie temperature of magnetic materials - Part 2: soft magnetic materials {译} 磁性材料居里温度的测量方法-第2部分：软磁材料 |
China National Standards temperature |
English PDF |
| GB/T 43873-2024 |
Test method for upper and lower limit temperature of ultra-thin glass annealing {译} 超薄玻璃退火上下限温度试验方法 |
China National Standards temperature |
English PDF |
| GB/T 43897-2024 |
Casting high-temperature alloys - Master alloys - Single crystals {译} 铸造高温合金-母合金-单晶 |
China National Standards temperature |
English PDF |
| GB/T 43997.1-2024 |
Surface temperature Thermal Infrared Remote Sensing Inversion - Part 1: Single Channel Method {译} 地表温度热红外遥感反演-第1部分：单通道法 |
China National Standards temperature |
English PDF |
| GB/T 43997.2-2024 |
Surface temperature Thermal Infrared Remote Sensing Inversion - Part 2: Split Window Method {译} 地表温度热红外遥感反演-第2部分：分裂窗法 |
China National Standards temperature |
English PDF |
| GB/T 44006-2024 |
Infrared Image temperature Representation Rules - RGB Method {译} 红外图像温度表示规则-RGB法 |
China National Standards temperature |
English PDF |
| GB/T 19665-2024 |
General specifications for infrared imaging human surface temperature screening devices {译} 红外成像人体表面测温筛查仪通用规范 |
China National Standards temperature |
English PDF |
| GB/T 43484-2023 |
Additive Manufacturing High temperature Alloy Powders for Laser Powder Bed Melting {译} 增材制造 激光粉末床熔融用高温合金粉末 |
China National Standards temperature |
English PDF |
| GB/Z 43521-2023 |
General guidelines for the design and analysis of ocean temperature difference energy conversion power plants {译} 海洋温差能转换电站设计和分析的一般指南 |
China National Standards temperature |
English PDF |
| GB/T 7000.224-2023 |
Luminaires Part 2-24: Special requirements Limited surface temperature luminaires {译} 灯具 第2-24部分：特殊要求 限制表面温度灯具 |
China National Standards temperature |
English PDF |
| GB/T 6803-2023 |
Drop weight test method for non-plastic transition temperature of ferritic steels {译} 铁素体钢的无塑性转变温度落锤试验方法 |
China National Standards temperature |
English PDF |
| GB/T 5072-2023 |
Refractory materials - Normal temperature compressive strength test method {译} 耐火材料 常温耐压强度试验方法 |
China National Standards temperature |
English PDF |
| GB/T 43307-2023 |
Determination of room temperature tensile properties of fine ceramic fiber single filaments {译} 精细陶瓷纤维 单丝室温拉伸性能的测定 |
China National Standards temperature |
English PDF |
| GB/T 43296-2023 |
Test method for room temperature bending fatigue properties of fine ceramics {译} 精细陶瓷室温弯曲疲劳性能试验方法 |
China National Standards temperature |
English PDF |
| GB/T 1965-2023 |
Porous ceramics - test method for room temperature flexural strength {译} 多孔陶瓷 室温弯曲强度试验方法 |
China National Standards temperature |
English PDF |
| GB/T 1964-2023 |
Porous ceramics - Test method for compressive strength at room temperature {译} 多孔陶瓷 室温压缩强度试验方法 |
China National Standards temperature |
English PDF |
| GB/T 30163-2023 |
Technical Specifications for Energy Saving of High Air temperature Top-Fired Hot Air Stoves for Blast Furnaces {译} 高炉用高风温顶燃式热风炉节能技术规范 |
China National Standards temperature |
English PDF |
| GB/T 43255-2023 |
Test method for low temperature cold starting performance of fuel cell electric vehicles {译} 燃料电池电动汽车低温冷起动性能试验方法 |
China National Standards temperature |
English PDF |
| GB/T 43118-2023 |
Corrosion of metals and alloys Test method for high-temperature corrosion of metallic materials under the action of deposits of salt, ash or other substances {译} 金属和合金的腐蚀 金属材料在盐、灰烬或其他物质的沉积物作用下进行高温腐蚀的试验方法 |
China National Standards temperature |
English PDF |
| GB/T 43115-2023 |
Metallic materials - Sheet and strip - Room temperature shear test methods {译} 金属材料 薄板和薄带 室温剪切试验方法 |
China National Standards temperature |
English PDF |
| GB/T 43092-2023 |
Electrochemical performance testing of lithium-ion battery cathode materials High temperature performance testing method {译} 锂离子电池正极材料电化学性能测试 高温性能测试方法 |
China National Standards temperature |
English PDF |
| GB/T 3780.30-2023 |
Carbon black Part 30: Determination of high temperature volatiles Thermogravimetric method {译} 炭黑 第30部分：高温挥发物的测定 热重法 |
China National Standards temperature |
English PDF |
| GB/T 42657-2023 |
Test method for infrared refractive index temperature coefficient of infrared optical glass - vertical incidence method {译} 红外光学玻璃红外折射率温度系数测试方法 垂直入射法 |
China National Standards temperature |
English PDF |
| GB/T 42653-2023 |
Glass high temperature viscosity test method {译} 玻璃高温黏度试验方法 |
China National Standards temperature |
English PDF |
| GB/T 35306-2023 |
Determination of carbon and oxygen content in silicon single crystal Low-temperature Fourier transform infrared spectroscopy {译} 硅单晶中碳、氧含量的测定 低温傅立叶变换红外光谱法 |
China National Standards temperature |
English PDF |
| GB/T 42667-2023 |
Test method for room temperature isobiaxial bending strength of fine ceramics - double loop method {译} 精细陶瓷室温等双轴弯曲强度试验方法 双环法 |
China National Standards temperature |
English PDF |
| GB/T 42655-2023 |
Test method for high temperature compression properties of continuous fiber reinforced ceramic matrix composites {译} 连续纤维增强陶瓷基复合材料高温压缩性能试验方法 |
China National Standards temperature |
English PDF |
| GB/T 42910-2023 |
Test method for high temperature compression shear strength of inorganic adhesives {译} 无机胶粘剂高温压缩剪切强度试验方法 |
China National Standards temperature |
English PDF |
| GB/T 42913-2023 |
Corrosion of metals and alloys Test methods for high-temperature corrosion of metallic materials embedded in salt, ash or other solids {译} 金属和合金的腐蚀 金属材料嵌入在盐、灰烬或其他固体中的高温腐蚀试验方法 |
China National Standards temperature |
English PDF |
| GB/T 42912-2023 |
Corrosion of metals and alloys Test methods for high-temperature corrosion of metallic materials under static immersion in molten salts or other liquids {译} 金属和合金的腐蚀 金属材料在静态浸入熔盐或其他液体条件下的高温腐蚀试验方法 |
China National Standards temperature |
English PDF |
| GB/T 42900-2023 |
High strain rate and high temperature compression test method for metallic materials {译} 金属材料 高应变速率高温压缩试验方法 |
China National Standards temperature |
English PDF |
| GB/T 713.5-2023 |
Steel plates and strips for pressure equipment Part 5: High manganese steels with specified low temperature properties {译} 承压设备用钢板和钢带 第5部分：规定低温性能的高锰钢 |
China National Standards temperature |
English PDF |
| GB/T 713.4-2023 |
Steel plates and strips for pressure equipment Part 4: Nickel alloy steels with specified low temperature properties {译} 承压设备用钢板和钢带 第4部分：规定低温性能的镍合金钢 |
China National Standards temperature |
English PDF |
| GB/T 713.3-2023 |
Steel plates and strips for pressure equipment Part 3: Low alloy steels with specified low temperature properties {译} 承压设备用钢板和钢带 第3部分：规定低温性能的低合金钢 |
China National Standards temperature |
English PDF |
| GB/T 713.2-2023 |
Steel plates and strips for pressure equipment Part 2: Non-alloy and alloy steels with specified temperature properties {译} 承压设备用钢板和钢带 第2部分：规定温度性能的非合金钢和合金钢 |
China National Standards temperature |
English PDF |
| GB/T 20818.14-2023 |
Industrial process measurement and control - Data structures and elements in process equipment catalogs - Part 14: List of properties (LOP) for electronic data exchange of temperature measuring equipment {译} 工业过程测量和控制 过程设备目录中的数据结构和元素 第14部分：温度测量设备电子数据交换用属性列表(LOP) |
China National Standards temperature |
English PDF |
| GB/T 42919.6-2023 |
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 6: Comparative method based on temperature modulation technology {译} 塑料 导热系数和热扩散系数的测定 第6部分：基于温度调制技术的比较法 |
China National Standards temperature |
English PDF |
| GB/T 42919.3-2023 |
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 3: temperature wave analysis method {译} 塑料 导热系数和热扩散系数的测定 第3部分：温度波分析法 |
China National Standards temperature |
English PDF |
| GB/T 40261.1-2023 |
Ergonomics of the thermal environment Assessment of the thermal environment in vehicles Part 1: Principles and methods of heat stress assessment and equivalent temperature determination {译} 热环境的人类工效学 交通工具内热环境评价 第1部分:热应激评估原理与方法和等效温度测定 |
China National Standards temperature |
English PDF |
| GB/T 5989-2023 |
Refractories - Test method for softening temperature under load (differential heating method) {译} 耐火材料 荷重软化温度试验方法(示差升温法) |
China National Standards temperature |
English PDF |
| GB/T 18034-2023 |
Specification for platinum-rhodium fine wire for rapid temperature measurement thermocouple {译} 快速测温热电偶用铂铑细偶丝规范 |
China National Standards temperature |
English PDF |
| GB/T 42567.3-2023 |
Reference conditions and procedures for testing transmitters for industrial process measurement Part 3: Specific procedures for temperature transmitters {译} 工业过程测量变送器试验的参比条件和程序 第3部分：温度变送器的特定程序 |
China National Standards temperature |
English PDF |
| GB/T 42516-2023 |
Chemical analysis method of high temperature shape memory alloy - determination of platinum content - thiourea complex precipitation method {译} 高温形状记忆合金化学分析方法 铂含量的测定 硫脲络合沉淀法 |
China National Standards temperature |
English PDF |
| GB/T 42603.2-2023 |
Moderate temperature molding materials for investment casting - Part 2: Test methods for serviceability {译} 熔模铸造中温模料 第2部分:使用性能试验方法 |
China National Standards temperature |
English PDF |
| GB/T 42603.1-2023 |
Moderate temperature molding materials for investment casting - Part 1: Test methods for physical properties {译} 熔模铸造中温模料 第1部分：物理性能试验方法 |
China National Standards temperature |
English PDF |
| GB/T 4937.23-2023 |
Semiconductor devices - Mechanical and climatic test methods - Part 23: High temperature operating life {译} 半导体器件 机械和气候试验方法 第23部分：高温工作寿命 |
China National Standards temperature |
English PDF |
| GB/T 4937.42-2023 |
Semiconductor devices - Mechanical and climatic test methods - Part 42: temperature and humidity storage {译} 半导体器件 机械和气候试验方法 第42部分：温湿度贮存 |
China National Standards temperature |
English PDF |
| GB/T 42368-2023 |
Method for Determination of Explosive Limits of Combustible Gas (Steam) under High temperature and High Pressure Conditions {译} 高温高压条件下可燃气体（蒸气）爆炸极限测定方法 |
China National Standards temperature |
English PDF |
| GB/T 25861-2023 |
Vapor compression cycle water source high temperature heat pump unit {译} 蒸气压缩循环水源高温热泵机组 |
China National Standards temperature |
English PDF |
| GB/T 10592-2023 |
High and low temperature test chamber technical conditions {译} 高低温试验箱技术条件 |
China National Standards temperature |
English PDF |
| GB/T 42472-2023 |
Critical current measurement Retained critical current of silver-coated Bi-2223 superconducting wire after double bending at room temperature {译} 临界电流测量 银包套Bi-2223超导线室温双弯曲后的保留临界电流 |
China National Standards temperature |
English PDF |
| GB/Z 28820.4-2022 |
Long-term radiation aging of polymers - Part 4: Effect of different temperatures and dose rates under radiation conditions {译} 聚合物长期辐射老化 第4部分：辐射条件下不同温度和剂量率的影响 |
China National Standards temperature |
English PDF |
| GB/T 41539-2022 |
Product specifications for satellite remote sensing images of land surface temperature {译} 卫星遥感影像地表温度产品规范 |
China National Standards temperature |
English PDF |
| GB/T 5170.18-2022 |
Test methods for environmental test equipment - Part 18: temperature/humidity combined cycle test equipment {译} 环境试验设备检验方法 第18部分：温度/湿度组合循环试验设备 |
China National Standards temperature |
English PDF |
| GB/T 41654-2022 |
Corrosion of metals and alloys - Method for metallographic examination of specimens after exposure to high temperature corrosive environments {译} 金属和合金的腐蚀 在高温腐蚀环境下暴露后试样的金相检验方法 |
China National Standards temperature |
English PDF |
| GB/T 41605-2022 |
Silicon nitride materials for rolling bearing balls - Test method for indentation fracture resistance at room temperature - Indentation method {译} 滚动轴承球用氮化硅材料 室温压痕断裂阻力试验方法 压痕法 |
China National Standards temperature |
English PDF |
| GB/T 41534-2022 |
Authenticity test of surface temperature remote sensing products {译} 地表温度遥感产品真实性检验 |
China National Standards temperature |
English PDF |
| GB/T 41521-2022 |
General technical requirements for multi-index nucleic acid constant temperature amplification detection microfluidic chip {译} 多指标核酸恒温扩增检测微流控芯片通用技术要求 |
China National Standards temperature |
English PDF |
| GB/T 41407-2022 |
Technical requirements of nucleic acid constant temperature amplification instrument based on microfluidic chip {译} 微流控芯片核酸恒温扩增仪技术要求 |
China National Standards temperature |
English PDF |
| GB/T 41490-2022 |
Test method for rolling contact fatigue of silicon nitride ceramics at room temperature ball plate method {译} 氮化硅陶瓷 室温下滚动接触疲劳试验方法 球板法 |
China National Standards temperature |
English PDF |
| GB/T 22688-2022 |
Pressure-type temperature controls for household and similar use 家用和类似用途压力式温度控制器 |
China National Standards temperature |
English PDF |
| GB/T 22687-2022 |
Bimetal temperature controls for household and similar use 家用和类似用途双金属温度控制器 |
China National Standards temperature |
English PDF |
| GB/T 24581-2022 |
Test method for Ⅲ and Ⅴ impurities content in single crystal silicon—Low temperature FT-IR analysis method 硅单晶中III、V族杂质含量的测定 低温傅立叶变换红外光谱法 |
China National Standards temperature |
English PDF |
| GB/T 1094.14-2022 |
Power transformers—Part 14: Liquid-immersed power transformer using high-temperature insulation materials 电力变压器 第14部分：采用高温绝缘材料的液浸式电力变压器 |
China National Standards temperature |
English PDF |
| GB/T 25857-2022 |
Low ambient temperature air source multi-connected heat pump (air conditioner) unit {译} 低环境温度空气源多联式热泵（空调）机组 |
China National Standards temperature |
English PDF |
| GB/T 14536.10-2022 |
Electric automatic controllers - Part 10: Particular requirements for temperature sensitive controllers {译} 电自动控制器 第10部分：温度敏感控制器的特殊要求 |
China National Standards temperature |
English PDF |
| GB/T 42261-2022 |
Metal and other inorganic coatings - thermal cycle test method for thermal barrier coatings under temperature gradient {译} 金属及其他无机覆盖层 温度梯度下热障涂层热循环试验方法 |
China National Standards temperature |
English PDF |
| GB/T 19721.5-2022 |
Marine Forecast and Warning Issues Part 5: Sea temperature Forecast Issues {译} 海洋预报和警报发布 第5部分：海温预报发布 |
China National Standards temperature |
English PDF |
| GB/T 41927-2022 |
Plastics - Thermoset molding compounds - Short-term performance evaluation at elevated temperatures {译} 塑料 热固性模塑料 高温下的短期性能评估 |
China National Standards temperature |
English PDF |
| GB/T 2406.3-2022 |
Plastics - Determination of combustion behavior by the oxygen index method - Part 3: High temperature test {译} 塑料 用氧指数法测定燃烧行为 第3部分：高温试验 |
China National Standards temperature |
English PDF |
| GB/T 19466.5-2022 |
Plastics - Differential scanning calorimetry (DSC) - Part 5: Determination of characteristic reaction curve temperature, time, enthalpy of reaction and conversion {译} 塑料 差示扫描量热法(DSC) 第5部分: 特征反应曲线温度、时间，反应焓和转化率的测定 |
China National Standards temperature |
English PDF |
| GB/T 33061.11-2022 |
Plastics - Determination of dynamic mechanical properties - Part 11: Glass transition temperature {译} 塑料 动态力学性能的测定 第11部分: 玻璃化转变温度 |
China National Standards temperature |
English PDF |
| GB/T 12085.23-2022 |
Optics and photonics - Environmental test methods - Part 23: Combined test for low pressure and low temperature, atmospheric temperature, high temperature or damp heat {译} 光学和光子学 环境试验方法 第23部分：低压与低温、大气温度、高温或湿热综合试验 |
China National Standards temperature |
English PDF |
| GB/T 12085.22-2022 |
Optics and photonics - Environmental test methods - Part 22: Combined test of low temperature, high temperature or temperature change with impact or random vibration {译} 光学和光子学 环境试验方法 第22部分: 低温、高温或温度变化与碰撞或随机振动综合试验 |
China National Standards temperature |
English PDF |
| GB/T 12085.2-2022 |
Optics and photonics - Environmental test methods - Part 2: Low temperature, high temperature, damp heat {译} 光学和光子学 环境试验方法 第2部分：低温、高温、湿热 |
China National Standards temperature |
English PDF |
| GB/T 41822-2022 |
Hot helium leak detection method for high temperature pressure-bearing parts of nuclear fusion reactor {译} 核聚变堆高温承压部件的热氦检漏方法 |
China National Standards temperature |
English PDF |
| GB/T 41641-2022 |
Measurement of mechanical properties - Tensile test method for REBCO strip at room temperature {译} 力学性能测量 REBCO带材室温拉伸试验方法 |
China National Standards temperature |
English PDF |
| GB/T 41742-2022 |
Low temperature sealing glass for optoelectronic devices {译} 光电器件用低温封接玻璃 |
China National Standards temperature |
English PDF |
| GB/T 41792-2022 |
Plastics - Films and sheets - Determination of cold cracking temperature {译} 塑料制品 薄膜和薄片 冷裂温度的测定 |
China National Standards temperature |
English PDF |
| GB/T 41707-2022 |
Copper-based arsenic removal agent at room temperature {译} 常温铜系脱砷剂 |
China National Standards temperature |
English PDF |
| GB/T 41640-2022 |
Critical current measurement Second-generation high-temperature superconducting long tape critical current and its uniformity along the length direction {译} 临界电流测量 第二代高温超导长带临界电流及其沿长度方向均匀性测量 |
China National Standards temperature |
English PDF |
| GB/T 41872-2022 |
Heat exchangers used in refrigeration systems and heat pumps—temperature, pressure and velocity three-field synergy performance test and evaluation method {译} 制冷系统及热泵用换热器 温度、压力和速度三场协同的性能测试和评价方法 |
China National Standards temperature |
English PDF |
| GB/T 40517-2021 |
Solar thermal storage system for low and medium temperature application 太阳能中低温蓄热装置 |
China National Standards temperature |
English PDF |
| GB/T 40515-2021 |
Ships and marine technology—Globe valves for use in low temperature applications—Design and testing requirements 船舶和海上技术 船用超低温截止阀 设计与试验要求 |
China National Standards temperature |
English PDF |
| GB/T 40380.2-2021 |
Metallic powders—Determination of apparent density and flow rate at elevated temperatures—Part 2: Determination of flow rate at elevated temperatures 金属粉末 高温时松装密度和流速的测定 第2部分：高温时流速的测定 |
China National Standards temperature |
English PDF |
| GB/T 40408-2021 |
Nuclear grade isostatic graphite for high temperature gas-cooled reactor internals 高温气冷堆堆内构件用核级等静压石墨 |
China National Standards temperature |
English PDF |
| GB/T 40404-2021 |
Slag material—Measurement of melting temperature—High temperature metallographic method 渣类材料 熔化温度的测定 高温金相法 |
China National Standards temperature |
English PDF |
| GB/T 40396-2021 |
Test method for glass transition temperature of polymer matrix composites—Dynamic mechanical analysis（DMA） 聚合物基复合材料玻璃化转变温度试验方法 动态力学分析法（DMA） |
China National Standards temperature |
English PDF |
| GB/T 40320-2021 |
Measuring method for mechanical melting temperature of aluminum alloy 铝合金力学熔点测试方法 |
China National Standards temperature |
English PDF |
| GB/T 1425-2021 |
Determination of melting temperature range for precious metals and their alloys—Testing method of thermal analysis 贵金属及其合金熔化温度范围的测定 热分析试验方法 |
China National Standards temperature |
English PDF |
| GB/T 40380.1-2021 |
Metallic powders—Determination of apparent density and flow rate at elevated temperatures—Part 1: Determination of apparent density at elevated temperatures 金属粉末 高温时松装密度和流速的测定 第1部分：高温时松装密度的测定 |
China National Standards temperature |
English PDF |
| GB/T 40286-2021 |
The performance testing method of bi-circulation unit for low-temperature waste heat recovery and utilization 低温双循环余热回收利用装置性能测试方法 |
China National Standards temperature |
English PDF |
| GB/T 31838.7-2021 |
Solid insulating materials - Dielecteric and resistive properties - Part 7: Resistive properties(DC method) - Measurement of volume resistance and volume resistivity at elevated temperatures 固体绝缘材料 介电和电阻特性 第7部分：电阻特性(DC方法) 高温下测量体积电阻和体积电阻率 |
China National Standards temperature |
English PDF |
| GB/T 22888-2021 |
Leather - Physical and mechanical tests - Determination of cold crack temperature of surface coatings 皮革 物理和机械试验 表面涂层低温脆裂温度的测定 |
China National Standards temperature |
English PDF |
| GB/T 2424.6-2021 |
Environmental testing-Part 3:Supporting documentation and guidance- Confirmation of the performance of temperature/humidity chambers 环境试验 第3部分：支持文件及导则 温度/湿度试验箱性能确认 |
China National Standards temperature |
English PDF |
| GB/T 2424.5-2021 |
Environmental testing—Part 3:Supporting documentation and guidance—Confirmation of the performance of temperature chambers 环境试验 第3部分：支持文件及导则 温度试验箱性能确认 |
China National Standards temperature |
English PDF |
| GB/T 19216.3-2021 |
Circuit integrity test for electric cables or optical fiber cables under fire conditions—Part 3:Test method for fire with shock at a temperature of at least 830℃ for cables of rated voltage up to and including 0.6/1 kV tested in a metal enclosure 在火焰条件下电缆或光缆的线路完整性试验 第3部分：火焰温度不低于830 ℃的供火并施加冲击振动，额定电压0.6/1 kV及以下电缆穿在金属管中进行的试验方法 |
China National Standards temperature |
English PDF |
| GB/T 19216.2-2021 |
Circuit integrity test for electric cables or optical fiber cables under fire conditions - Part 2: Test method for fire with shock at a temperature of at least 830 ℃ for cables of rated voltage up to and including 0.6/1 kV and with an overall diameter not 在火焰条件下电缆或光缆的线路完整性试验 第2部分：火焰温度不低于830 ℃的供火并施加冲击振动，额定电压0.6/1 kV及以下外径不超过20 mm电缆的试验方法 |
China National Standards temperature |
English PDF |
| GB/T 19216.1-2021 |
Circuit integrity test for electric cables or optical fiber cables under fire conditions-Part 1:Test method for fire with shock at atemperature of at least 830 ℃ for cables of rated voltage up to and including 0.6/ 1 kV and with an overall diameter exceed 在火焰条件下电缆或光缆的线路完整性试验 第1部分：火焰温度不低于830 ℃的供火并施加冲击振动，额定电压0.6/1 kV及以下外径超过20 mm电缆的试验方法 |
China National Standards temperature |
English PDF |
| GB/T 39933-2021 |
Rotational moulding—Test method for low temperature impact 滚塑成型 低温冲击试验 |
China National Standards temperature |
English PDF |
| GB/T 39828-2021 |
Test method for determining elastic modulus of thick ceramic coating at elevated temperature 陶瓷厚涂层的高温弹性模量试验方法 |
China National Standards temperature |
English PDF |
| GB/T 19136-2021 |
Testing method of the accelerated storage stability at elevated temperature for pesticides 农药热储稳定性测定方法 |
China National Standards temperature |
English PDF |
| GB/T 41036-2021 |
General specification for super high-low temperature circular electrical connector for space applications 宇航用超高低温圆形电连接器通用规范 |
China National Standards temperature |
English PDF |
| GB/T 228.1-2021 |
Metallic materials—Tensile testing—Part 1: Method of test at room temperature 金属材料 拉伸试验 第1部分:室温试验方法 |
China National Standards temperature |
English PDF |
| GB/T 40939-2021 |
General requirements for low temperature medical cold store 低温医用冷库通用技术要求 |
China National Standards temperature |
English PDF |
| GB/T 18426-2021 |
Rubber-or plastics-coated fabrics—Low-temperature bend test 橡胶或塑料涂覆织物 低温弯曲试验 |
China National Standards temperature |
English PDF |
| GB/T 40794-2021 |
Measurement method of irreversible magnetic flux loss due to high temperature of rare earth permanent magnet 稀土永磁材料高温磁通不可逆损失检测方法 |
China National Standards temperature |
English PDF |
| GB/T 18113-2021 |
High temperature lanthanum chromite electric heating module 铬酸镧高温电热元件 |
China National Standards temperature |
English PDF |
| GB/T 1687.4-2021 |
Rubber,vulcanized—Determination of temperature rise and resistance to fatigue in flexometer testing—Part 4: Constant-stress flexometer 硫化橡胶 在屈挠试验中温升和耐疲劳性能的测定 第4部分：恒应力屈挠试验 |
China National Standards temperature |
English PDF |
| GB/T 40703-2021 |
Design specifications of medium temperature solar heating system for industrial applications 太阳能中温工业热利用系统设计规范 |
China National Standards temperature |
English PDF |
| GB/T 39151-2020 |
Nickel beryllium titanium alloy strip for high temperature elastic component 高温弹性元件用镍铍钛合金带材 |
China National Standards temperature |
English PDF |
| GB/T 38924.2-2020 |
Environmental test methods for civil small and light unmanned aircraft system—Part 2: Low-temperature test 民用轻小型无人机系统环境试验方法 第2部分: 低温试验 |
China National Standards temperature |
English PDF |
| GB/T 38924.3-2020 |
Environmental test methods for civil small and light unmanned aircraft system—Part 3: High-temperature test 民用轻小型无人机系统环境试验方法 第3部分：高温试验 |
China National Standards temperature |
English PDF |
| GB/T 38924.4-2020 |
Environmental test methods for civil small and light unmanned aircraft system—Part 4: temperature and altitude test 民用轻小型无人机系统环境试验方法 第4部分：温度和高度试验 |
China National Standards temperature |
English PDF |
| GB/T 38948-2020 |
Evaluation method for the cracking resistance of asphalt mixture at low temperature 沥青混合料低温抗裂性能评价方法 |
China National Standards temperature |
English PDF |
| GB/T 38917-2020 |
High temperature titanium alloy bars for aerospace 航空航天用高温钛合金棒材 |
China National Standards temperature |
English PDF |
| GB/T 38916-2020 |
High temperature titanium alloy plate and sheet for aerospace 航空航天用高温钛合金板材 |
China National Standards temperature |
English PDF |
| GB/T 38915-2020 |
High temperature titanium alloy forgings for aerospace 航空航天用高温钛合金锻件 |
China National Standards temperature |
English PDF |
| GB/T 38912-2020 |
Test method for closed-end burst of zirconium tubes at room temperature 锆管室温闭端爆破试验方法 |
China National Standards temperature |
English PDF |
| GB/T 25127.1-2020 |
Low ambient temperature air source heat pump （water chilling）packages—Part 1：Heat pump （water chilling）packages for industrial & commercial and similar application 低环境温度空气源热泵（冷水）机组 第1部分：工业或商业用及类似用途的热泵（冷水）机组 |
China National Standards temperature |
English PDF |
| GB/T 25127.2-2020 |
Low ambient temperature air source heat pump （water chilling）packages—Part 2：Heat pump （water chilling）packages for household and similar application 低环境温度空气源热泵（冷水）机组 第2部分：户用及类似用途的热泵（冷水）机组 |
China National Standards temperature |
English PDF |
| GB/T 38936-2020 |
High temperature carburizing steel for bearing 高温渗碳轴承钢 |
China National Standards temperature |
English PDF |
| GB/T 38886-2020 |
High temperature bearing steel 高温轴承钢 |
China National Standards temperature |
English PDF |
| GB/T 38884-2020 |
High temperature stainless steels for bearing 高温不锈轴承钢 |
China National Standards temperature |
English PDF |
| GB/T 38841-2020 |
Mechanical properties measurement—Room temperature tensile test of reacted Nb3Sn composite superconductors 力学性能测量 反应后的Nb3Sn复合超导线室温拉伸试验方法 |
China National Standards temperature |
English PDF |
| GB/T 38804-2020 |
Test method for oxidation of metallic materials exposed in high-temperature steam 金属材料高温蒸汽氧化试验方法 |
China National Standards temperature |
English PDF |
| GB/T 2423.27-2020 |
Environmental testing—Part 2: Test methods—Test method and guidance: Combined temperature or temperature and humidity with low air pressure tests 环境试验 第2部分：试验方法 试验方法和导则：温度/低气压或温度/湿度/低气压综合试验 |
China National Standards temperature |
English PDF |
| GB 27955-2020 |
Hygienic requirements for low-temperature hydrogen peroxide gas plasma sterilizer 过氧化氢气体等离子体低温灭菌器卫生要求 |
China National Standards temperature |
English PDF |
| GB/T 5137.3-2020 |
Test methods of safety glazing materials used on road vehicles—Part 3:Radiation,high temperature,humidity,fire and simulated weathering resistance tests 汽车安全玻璃试验方法 第3部分：耐辐照、高温、潮湿、燃烧和耐模拟气候试验 |
China National Standards temperature |
English PDF |
| GB/T 23605-2020 |
Determination of β transus temperature of titanium alloys 钛合金β转变温度测定方法 |
China National Standards temperature |
English PDF |
| GB/T 7964-2020 |
Sintered metal materials(excluding hardmetal)--Tension testing at room temperature 烧结金属材料(不包括硬质合金) 室温拉伸试验 |
China National Standards temperature |
English PDF |
| GB/T 38534-2020 |
Test method for tensile properties of oriented fibre reinforced polymer matrix composite materials at ultra-low temperature 定向纤维增强聚合物基复合材料超低温拉伸性能试验方法 |
China National Standards temperature |
English PDF |
| GB/T 38515-2020 |
The method for high temperature mechanical properties of quartz fabric-reinforced resin matrix composite materials 石英纤维织物增强树脂基复合材料高温力学性能试验方法 |
China National Standards temperature |
English PDF |
| GB/T 39682-2020 |
Fine ceramics—Determination of elastic modulus at high temperature or ultra-high temperature—Split ring relative method 精细陶瓷 高温和超高温弹性模量的测定 缺口环相对法 |
China National Standards temperature |
English PDF |
| GB/T 7758-2020 |
Rubber, vulcanized—Determination of low-temperature characteristics—Temperature-retraction procedure (TR test) 硫化橡胶 低温性能的测定 温度回缩程序（TR 试验） |
China National Standards temperature |
English PDF |
| GB/T 6036-2020 |
Rubber,vulcanized or thermoplastic—Determination of low-temperature stiffening(Gehman test) 硫化橡胶或热塑性橡胶 低温刚性的测定（吉门试验） |
China National Standards temperature |
English PDF |
| GB/T 39692-2020 |
Rubber,vulcanized or thermoplastic—Low temperature testing—General introduction and guide 硫化橡胶或热塑性橡胶 低温试验 概述与指南 |
China National Standards temperature |
English PDF |
| GB/T 32065.8-2020 |
Environmental test methods for oceanographic instruments—Part 8：Change of temperature test 海洋仪器环境试验方法 第8部分：温度变化试验 |
China National Standards temperature |
English PDF |
| GB/T 28799.5-2020 |
Polyethylene of raised temperature resistance (PE-RT) piping systems for hot and cold water installations—Part 5： Fitness for purpose of the system 冷热水用耐热聚乙烯(PE-RT)管道系统 第5部分：系统适用性 |
China National Standards temperature |
English PDF |
| GB/T 28799.3-2020 |
Polyethylene of raised temperature resistance (PE-RT) piping systems for hot and cold water installations—Part 3: Fittings 冷热水用耐热聚乙烯(PE-RT)管道系统 第3部分：管件 |
China National Standards temperature |
English PDF |
| GB/T 28799.2-2020 |
Polyethylene of raised temperature resistance (PE-RT) piping systems for hot and cold water installations—Part 2: Pipes 冷热水用耐热聚乙烯(PE-RT)管道系统 第2部分：管材 |
China National Standards temperature |
English PDF |
| GB/T 28799.1-2020 |
Polyethylene of raised temperature resistance（PE-RT）piping systems for hot and cold water installations—Part 1: General 冷热水用耐热聚乙烯(PE-RT)管道系统 第1部分：总则 |
China National Standards temperature |
English PDF |
| GB/T 3098.24-2020 |
Mechanical properties of fasteners—Stainless steel and nickel alloys bolts, screws, studs and nuts for high temperature applications 紧固件机械性能 高温用不锈钢和镍合金螺栓、螺钉、螺柱和螺母 |
China National Standards temperature |
English PDF |
| GB/T 39249-2020 |
Rubber and plastics hoses and tubing—Textile-reinforced types—Sub-ambient temperature crush test 橡胶和塑料软管及非增强软管 织物增强型 低温压扁试验 |
China National Standards temperature |
English PDF |
| GB/T 38298-2019 |
Test method of auto-ignition temperature for solid chemicals 固体化学品自动点火温度的试验方法 |
China National Standards temperature |
English PDF |
| GB/T 23711.3-2019 |
Test method for pressure vessels lined with plastics—Part 3:High-temperature inspection 塑料衬里压力容器试验方法 第3部分：耐高温检验 |
China National Standards temperature |
English PDF |
| GB/T 23711.2-2019 |
Test method for pressure vessels lined with plastics—Part 2:Low-temperature testing 塑料衬里压力容器试验方法 第2部分：耐低温试验 |
China National Standards temperature |
English PDF |
| GB/T 4797.4-2019 |
Classification of environmental conditions—Environmental conditions appearing in nature—Solar radiation and temperature 环境条件分类 自然环境条件 太阳辐射与温度 |
China National Standards temperature |
English PDF |
| GB/T 1685.2-2019 |
Rubber, vulcanized or thermoplastic—Determination of stress relaxation in compression—Part 2: Testing with temperature cycling 硫化橡胶或热塑性橡胶 压缩应力松弛的测定 第2部分：循环温度下试验 |
China National Standards temperature |
English PDF |
| GB/T 38430-2019 |
Corrosion of metals and alloys—Test method for isothermal-exposure oxidation testing under high-temperature corrosion conditions for metallic materials 金属和合金的腐蚀 金属材料在高温腐蚀条件下的等温暴露氧化试验方法 |
China National Standards temperature |
English PDF |
| GB/T 38426-2019 |
Test method for thermal resistance and use temperature of sleeping bags 睡袋的热阻和使用温度的测定方法 |
China National Standards temperature |
English PDF |
| GB/T 38375-2019 |
Guide for planning and design of food low temperature distribution center 食品低温配送中心规划设计指南 |
China National Standards temperature |
English PDF |
| GB/T 38298-2019 |
Test method of auto-ignition temperature for solid chemicals 固体化学品自动点火温度的试验方法 |
China National Standards temperature |
English PDF |
| GB/T 23711.3-2019 |
Test method for pressure vessels lined with plastics—Part 3:High-temperature inspection 塑料衬里压力容器试验方法 第3部分：耐高温检验 |
China National Standards temperature |
English PDF |
| GB/T 23711.2-2019 |
Test method for pressure vessels lined with plastics—Part 2:Low-temperature testing 塑料衬里压力容器试验方法 第2部分：耐低温试验 |
China National Standards temperature |
English PDF |
| GB/T 4797.4-2019 |
Classification of environmental conditions—Environmental conditions appearing in nature—Solar radiation and temperature 环境条件分类 自然环境条件 太阳辐射与温度 |
China National Standards temperature |
English PDF |
| GB/T 1685.2-2019 |
Rubber, vulcanized or thermoplastic—Determination of stress relaxation in compression—Part 2: Testing with temperature cycling 硫化橡胶或热塑性橡胶 压缩应力松弛的测定 第2部分：循环温度下试验 |
China National Standards temperature |
English PDF |
| GB/T 2423.35-2019 |
Environmental testing—Part 2:Tests and guidance—Combined climatic(temperature/humidity)and dynamic(vibration/shock) tests 环境试验 第2部分：试验和导则 气候(温度、湿度)和动力学(振动、冲击)综合试验 |
China National Standards temperature |
English PDF |
| GB/T 37945-2019 |
Materials for organic light emitting diode display(OLED)—Test method of glass transfer temperature—Differential scanning calorimetry (DSC) 有机发光二极管显示器用材料 玻璃化转变温度测试方法 差热法 |
China National Standards temperature |
English PDF |
| GB/T 37901-2019 |
Technical requirements for laser welding of high temperature titanium alloy 高温钛合金激光焊接技术要求 |
China National Standards temperature |
English PDF |
| GB/T 37819-2019 |
Bi-circulation power generation unit for low-temperature waste heat recovery 低温余热双循环发电装置 |
China National Standards temperature |
English PDF |
| GB/T 37783-2019 |
Metallic materials—High strain rate tensile test method at elevated temperature 金属材料 高应变速率高温拉伸试验方法 |
China National Standards temperature |
English PDF |
| GB/T 228.3-2019 |
Metallic materials—Tensile testing—Part 3: Method of test at low temperature 金属材料 拉伸试验 第3部分：低温试验方法 |
China National Standards temperature |
English PDF |
| GB/T 37603-2019 |
Medium temperature brazing filler metals of aluminum alloys 铝合金中温钎料 |
China National Standards temperature |
English PDF |
| GB/T 37602-2019 |
Ship and offshore engineering steel for low temperature service 船舶及海洋工程用低温韧性钢 |
China National Standards temperature |
English PDF |
| GB/T 37577-2019 |
Welded large diameter steel pipes for low-temperature-service piping
低温管道用大直径焊接钢管 |
China National Standards temperature |
English PDF |
| Find out:500Items | To Page of: First -Previous-Next -Last | 1 2 3 |
+86-755-25831330
